For vocal limiter settings in Logic Pro, set the stock Limiter to Gain +2 to +4 dB and Output Level -1 dB, so it only trims the loudest peaks by 1 to 3 dB. If you use Adaptive Limiter, set Out Ceiling to -1 dB and push Gain until the peaks drop by the same 1 to 3 dB.
A limiter on a vocal is a safety net. It sits after your compressor and catches the few peaks that still jump out. The settings below are starting points, so adjust them by ear for your voice.
Vocal limiter settings in Logic Pro: the quick version
- Compress the vocal first. The limiter should not do the compressor's job.
- Insert Limiter as the last plugin on the vocal track, after the de-esser.
- Set Output Level to -1 dB so the vocal never hits 0 dB.
- Raise Gain from 0 dB in small steps, up to about +4 dB, until the loudest words lose 1 to 3 dB.
- Turn on True Peak Detection if you want the ceiling to catch peaks between samples.
- Toggle the plugin on and off at equal loudness. If the voice sounds flatter or breathes, lower Gain.
What are the best Limiter settings for vocals?
| Control | Starting value | What it does |
|---|---|---|
| Gain | +2 to +4 dB | Pushes the signal into the limiter. More gain means more limiting. |
| Output Level | -1 dB | Sets the ceiling the signal cannot pass. |
| Lookahead | Default, then adjust by ear | Gives the limiter time to react to a peak before it arrives. |
| Release | 50 to 100 ms | How fast the gain recovers after a peak. Too fast can sound grainy. |
| True Peak Detection | On | Catches peaks that fall between samples. |
Watch the gain reduction meter. On a vocal it should move by 1 to 3 dB on the loudest words and stay near 0 dB the rest of the time. If it moves all the time, the compressor ahead of it needs work, not the limiter.
Step: add the limiter to the chain
Put the limiter last, after Channel EQ, the compressor and the de-esser. Set the values above and check the peaks. A Thir13een preset loads that whole chain on your vocal in one click, with the limiter already in place, so you can hear a clean starting point and adjust it. Try the Logic Pro Starter Pack.
Limiter or Adaptive Limiter for vocals?
Both are stock in Logic Pro. Use the plain Limiter when you want a simple, clear ceiling on a vocal track. Use Adaptive Limiter when you want a bit more shaping, because it adds an Attack control next to Gain, Out Ceiling, Lookahead and Release.
For Adaptive Limiter, start with Out Ceiling at -1 dB, Release at 50 to 100 ms, and the default Attack and Lookahead. Raise Gain until the loudest words drop by 1 to 3 dB. Then move Attack and Release one at a time. If the vocal loses its punch, slow the Attack a little. If it sounds pumpy, lengthen the Release.
Where does the limiter go on a vocal chain?
The order matters. A common vocal chain runs: high-pass and EQ cuts, compression, de-esser, then limiter. The compressor evens out the performance. Our vocal compression settings for Logic Pro cover that step.
Put the de-esser before the limiter. A limiter that hits sharp "s" sounds can make them stick out more, so tame them first with the de-esser settings for Logic Pro. For the full signal order, see Logic Pro vocal settings.
Common limiter mistakes on vocals
- Pushing Gain too high. More than 4 to 5 dB of limiting flattens the voice and brings up breaths and noise.
- Using the limiter as the main compressor. Compress first and keep the limiter light.
- Skipping the ceiling. Leave Output Level at -1 dB, not 0 dB, so later processing has headroom.
- Judging by loudness. A louder vocal always sounds better for a moment. Match the level when you toggle the plugin.
- Limiting a muddy vocal. A limiter reacts to loud low-mid energy, so fix the tone first with our guide to fixing muddy vocals.
Try a preset on your vocal
Download Toronto Warmth, our free preset for Logic Pro X, load it on your vocal and hear a finished chain. For more options, browse the Logic Pro X vocal presets.
FAQ
Should I put a limiter on vocals?
Yes, if a few peaks still jump out after compression. Keep it light, with 1 to 3 dB of gain reduction. If the vocal already sits steady, you can skip it.
What Output Level should a vocal limiter use?
Start at -1 dB. This keeps the vocal under 0 dB and leaves headroom for the rest of the mix and for later processing.
Is a limiter the same as a compressor?
No. A compressor lowers the level above a threshold in a gentle ratio. A limiter stops the signal from passing a ceiling. On a vocal, the compressor shapes the performance and the limiter catches the last peaks.
How much limiting is too much on a vocal?
More than about 4 dB of gain reduction on a regular basis is too much. If the voice sounds flat, breathy or pumpy, lower Gain and let the compressor do more of the work.


