Shop presets

Vocal Harmonies in Logic Pro: Stack, Pan and Mix

Logic Pro X vocal presets. Add a 2nd preset for 50% off in the cart.Logic Pro X vocal presets. Logic Pro X deal: buy 2 presets, get 1 FREE.

To make vocal harmonies in Logic Pro, record each harmony as its own take, group the takes into a Summing Stack, then tighten timing and tuning with Flex Time and Flex Pitch. Pan the layers, set them 6 to 10 dB under the lead, and process the stack as one bus with EQ, compression and a reverb send.

The values below are starting points. Your voice, mic and song will change them, so adjust by ear.

How do I record vocal harmonies in Logic Pro?

Record the lead vocal first and get it right. Then record each harmony part on a new track, one part per take. Sing every part with the same mic, the same distance and the same energy as the lead.

  • Record a high harmony and a low harmony first. Most songs need only these two.
  • Record each part twice on separate tracks. This is called double tracking, and it makes the part sound wider and fuller.
  • Keep peaks around -12 to -6 dBFS, as with the lead.
  • Name each track, for example "Harm High L" and "Harm High R". Clear names save time in the mix.

How do I group harmonies into a Track Stack?

Select all harmony tracks, then choose Track > Create Track Stack. Pick Summing Stack. Logic sends the harmony tracks into one bus, and you get one channel strip that controls them all.

  • A Summing Stack is the right choice for harmonies, because you can put plugins and sends on the whole group.
  • A Folder Stack only tidies the track list. It has no shared channel strip for processing.
  • Name the stack "Harmonies". Keep the lead vocal outside it, on its own track.

Want the stack processed in one click?

Once the harmonies sit in a Summing Stack, a Thir13een preset on that stack's channel strip loads an EQ, compressor, de-esser and reverb for all layers at once, so they sound like one group. Try the Vocal Preset Starter Pack for Logic Pro X on the stack and compare three looks in one chorus. Or browse the Logic Pro X vocal presets. Need help loading one? Read how to install Logic Pro vocal presets.

How do I pan and balance harmony layers?

  • Pan the two takes of each part apart. For example, high harmony take 1 at 40 percent left and take 2 at 40 percent right.
  • Pan the low harmony the same way, a little wider or narrower than the high part.
  • Keep the lead vocal in the center.
  • Set the harmony stack 6 to 10 dB under the lead. Lower it until you notice the harmony only when you mute it.
  • Check the mix in mono. If the harmonies vanish or thin out, reduce the panning.

How do I tighten timing and pitch on harmonies?

Harmonies blend when each word starts and ends together with the lead. Open the Track Editor on a harmony track and switch on Flex mode.

  • Flex Time: pick Flex Time as the Flex mode, then drag the start of a word to match the lead. Fix the starts of words first, then the ends. Most clashing comes from "s", "t" and "k" sounds that land late.
  • Flex Pitch: pick Flex Pitch to see each note as a block. Use Correct Pitch on notes that sound sharp or flat. Do not set it to full correction on every note, because that makes layers sound robotic.
  • Leave small differences in timing and pitch between the double-tracked takes. They create the natural width you want.

What EQ and compression should I put on a harmony stack?

Use the channel strip of the Summing Stack, so one chain shapes every layer.

  • Channel EQ: high-pass at 120 to 150 Hz. Cut 2 to 3 dB around 250 to 400 Hz if the stack sounds boxy.
  • Presence: keep it lower than the lead. Boost 1 dB around 3 to 4 kHz at most, so harmonies stay behind the lead.
  • Compressor: ratio 3:1, attack 15 to 25 ms, release 80 to 120 ms. Aim for 2 to 4 dB of gain reduction. See vocal compression settings in Logic Pro for more.
  • De-esser: stacked "s" sounds add up. If the stack sounds sharp, use DeEsser 2 and reduce 2 to 4 dB at 5 to 8 kHz.

How much reverb should harmonies get?

Use a send on the stack, not a reverb on each track. Send the Summing Stack to a bus with ChromaVerb. A plate or room of 1.2 to 2 seconds with a pre-delay of 30 to 50 ms works well. Set the send so the harmonies sit slightly more in the space than the lead. That pushes them behind the lead and leaves the lead clear. For more, see reverb and delay for vocals: settings cheat sheet.

Step Where Starting value What it does
Record Separate tracks 2 takes per part, peaks -12 to -6 dBFS Width and fullness
Group Summing Stack One stack named "Harmonies" One bus for all layers
Pan Each track Takes apart, about 40 percent left and right Stereo width
Level Stack fader 6 to 10 dB under the lead Support, not compete
Timing and pitch Flex Time, Flex Pitch Fix word starts, correct only off notes Layers blend
EQ Channel EQ on stack High-pass 120 to 150 Hz, cut 2 to 3 dB at 250 to 400 Hz Clean, not boxy
Compression Compressor on stack 3:1, attack 15 to 25 ms, 2 to 4 dB reduction Even group level
Reverb Send to ChromaVerb 1.2 to 2 s, pre-delay 30 to 50 ms Depth behind the lead

Using GarageBand? Read how to do vocal harmonies in GarageBand. For the lead vocal chain, see the vocal chain guide for Logic Pro.

What mistakes make harmonies sound messy?

  • Layers that are as loud as the lead.
  • Late word starts that were never fixed with Flex Time.
  • Full pitch correction on every note.
  • Too much low end. Eight layers of low mids sound muddy.
  • A separate reverb on every track, instead of one send.

Try a preset on your vocal

Download Toronto Warmth, our free preset for Logic Pro X, load it on your lead vocal, then build your harmony stack with the steps above. For more options, browse the Logic Pro X vocal presets or read our free vocal presets guide.

FAQ

How many harmony layers do I need?

Start with one high and one low part, each recorded twice. That gives four tracks and a full sound. Add more parts only when the chorus still feels thin.

Should harmonies be louder or quieter than the lead?

Quieter. Set the stack about 6 to 10 dB under the lead. Mute the stack, then unmute it. You should notice the song feels fuller, but the lead still leads.

Can I use a vocal preset on a harmony stack?

Yes. Load the preset on the Summing Stack's channel strip, so one chain covers every layer. Then lower the presence boost and the compression a little, so the harmonies stay behind the lead.

Voltar ao blog

Deixe um comentário

Presets Vocais para Logic Pro X