Shop presets

GarageBand Vocal EQ Settings: Hz and dB to Start With

GarageBand vocal presets. Add a 2nd preset for 50% off in the cart.GarageBand vocal presets. GarageBand deal: buy 1 preset, get 1 FREE.

For a vocal in GarageBand, start with a high-pass filter at 80 to 100 Hz, cut 2 to 4 dB around 250 to 400 Hz to clear mud, boost 2 to 3 dB around 3 to 5 kHz for presence, and add a gentle lift above 10 kHz for air. Finish with a small cut where the voice sounds harsh. Use these as starting points and adjust by ear.

Make small moves. Most vocals need cuts first and only a little boost at the end.

Where does EQ go in the GarageBand vocal chain?

Put an EQ first, then the Compressor, then reverb and delay. A cleaned-up signal reaches the compressor, so it does not squash the rumble and mud you plan to remove. You can add a second EQ after the compressor for gentle shaping. In GarageBand, open the Smart Controls and Plug-ins area for the track and choose the Channel EQ or Visual EQ. For the full order, read the GarageBand vocal chain guide.

What EQ settings should I use on a vocal in GarageBand?

Step 1: High-pass filter at 80 to 100 Hz

Cut everything below 80 to 100 Hz. A vocal has little useful sound down there, only desk bumps, breaths and room rumble. Use a steep slope. If the voice starts to sound thin, move the filter down 10 to 20 Hz.

Step 2: Cut mud at 250 to 400 Hz

Boxy, cloudy vocals usually have too much energy here. Raise a narrow boost, sweep between 250 and 400 Hz until the sound gets worst, then turn it into a 2 to 4 dB cut. Play the vocal with the beat and check that the voice still sounds full.

Step 3: Add presence at 3 to 5 kHz

Boost 2 to 3 dB with a wide curve between 3 and 5 kHz. This helps consonants and makes the vocal stand out against the beat. Stop if the voice starts to sound sharp or nasal.

Step 4: Add air above 10 kHz

Use a high shelf at 10 to 12 kHz and lift 1 to 2 dB. This adds a bright, open top end. A noisy recording will also lift hiss, so listen for that.

Step 5: Cut harshness at 2 to 4 kHz

If the vocal hurts after the presence boost, make a narrow cut of 2 to 3 dB around 2 to 4 kHz. Find the exact spot by sweeping a boost until the harshness jumps out, then cut there. If "s" sounds are still sharp, the problem is sibilance, not EQ, and you need a de-esser.

Let a preset build the chain

Setting every band by hand takes time. A Thir13een GarageBand preset loads a finished chain on the track, with the EQ, compression and effects already set. You can hear it at once, then tweak each setting. The presets work with GarageBand's built-in effects, so you need no extra plugins. Browse the GarageBand vocal presets.

What are the starting points for male and female vocals?

These ranges shift with each voice. Treat them as a first guess.

  • Male vocal: high-pass at 80 Hz, cut mud around 200 to 300 Hz, presence at 3 to 4 kHz, air at 10 kHz and above.
  • Female vocal: high-pass at 100 Hz, cut mud around 300 to 400 Hz, presence at 4 to 5 kHz, air at 12 kHz and above.

Our vocal EQ cheat sheet lists more frequency ranges.

What mistakes should I avoid with vocal EQ?

  • Boosting before you cut. Remove problems first, then add.
  • Judging at different volumes. Switch the EQ off and on at the same level.
  • Using large boosts. Keep each one to 3 dB or less.
  • Setting EQ with the vocal soloed. Check it with the beat playing.
  • Fixing a bad recording with EQ. Re-record if the room sound is heavy.

For more on levels and effects, see GarageBand vocal settings.

Try a preset on your vocal

Download Toronto Warmth, our free preset. It is built for Logic Pro X, so it only helps if you also use Logic. GarageBand users can browse the GarageBand vocal presets collection.

FAQ

What is the best EQ setting for vocals in GarageBand?

High-pass at 80 to 100 Hz, a 2 to 4 dB cut at 250 to 400 Hz, a 2 to 3 dB boost at 3 to 5 kHz, and a small shelf lift above 10 kHz. Adjust each by ear.

Should I EQ before or after compression?

Do the cuts before the compressor so it does not react to mud or rumble. Add any gentle boosts after it if the tone still needs help.

Where do I find the EQ in GarageBand?

Select the vocal track and open the Plug-ins area in the Smart Controls. Choose the Channel EQ or Visual EQ there.

How do I make my vocal sound clearer in GarageBand?

Cut the low rumble with a high-pass filter, clear the mud near 250 to 400 Hz, and add a small presence boost at 3 to 5 kHz.

Voltar ao blog

Deixe um comentário

Presets Vocais para Logic Pro X