Shop presets

Male Vocal EQ Settings in Logic Pro

Logic Pro X vocal presets. Add a 2nd preset for 50% off in the cart.Logic Pro X vocal presets. Logic Pro X deal: buy 2 presets, get 1 FREE.

For a male vocal in Logic Pro, start with the stock Channel EQ: a high-pass filter at about 80 Hz, a small cut between 200 and 300 Hz to clear mud, a gentle boost between 3 and 5 kHz for presence, and a soft high shelf above 10 kHz for air. These numbers are starting points, not rules. Every voice and mic is different, so use your ears and move each band until the vocal sounds clear next to the beat.

Below are the exact settings, in the order to set them. Want the full theory behind each range? See our vocal EQ cheat sheet.

Male vocal EQ settings in Logic Pro: the quick version

  1. Open Channel EQ on the vocal track.
  2. High-pass filter at about 80 Hz.
  3. Cut 200 to 300 Hz by 2 to 4 dB with a medium-narrow band.
  4. Boost 3 to 5 kHz by 1 to 3 dB for presence.
  5. Add a high shelf above 10 kHz, +1 to +2 dB, for air.
  6. Check sibilance and use a de-esser if "s" sounds are harsh.

Step 1: Add Channel EQ and set the high-pass

Click an empty Audio FX slot on the vocal channel and choose EQ, then Channel EQ. Turn on the high-pass filter, the leftmost band, and set it to about 80 Hz. This removes rumble, desk bumps and low noise that the voice does not need. If the voice sounds thin afterward, lower the filter toward 60 Hz. If the track still has low rumble, raise it toward 100 Hz.

Step 2: Cut the mud between 200 and 300 Hz

Low male voices often sound boxy or muddy in this range. Use one of the parametric bands. Set a boost of 6 dB, then sweep slowly between 200 and 300 Hz until the boxy sound gets worse. That is the problem spot. Now turn the gain down to a cut of 2 to 4 dB, with a medium-narrow Q. Small cuts sound more natural than deep ones.

Step 3: Add presence at 3 to 5 kHz

This range helps the words cut through the beat. Add a broad boost of 1 to 3 dB between 3 and 5 kHz. Listen to the consonants: if the words become easier to understand, the boost is working. If the voice sounds sharp or tiring, pull it back or move the center up or down by a few hundred Hz.

Step 4: Add air with a high shelf

Turn on the high shelf and set it above 10 kHz. Raise it 1 to 2 dB. This adds a little openness at the top. Use less on a bright mic or a noisy recording, because the boost lifts hiss as well.

Load this chain in one click

Setting EQ by hand is the best way to learn. When you want a finished starting point, the Auto-Tune Vocal Preset for Logic Pro X loads a ready-made vocal channel strip that you can adjust to your own voice. More options sit in the Logic Pro X vocal presets collection.

A note on de-essing

Boosting presence and air can make "s" and "t" sounds harsh. If that happens, add a de-esser after the EQ and set it to the sibilance range, usually somewhere between 5 and 8 kHz for many voices. Reduce only as much as needed. Check the result with the full mix playing.

Common mistakes

  • Boosting with the track soloed. A vocal can sound great alone and wrong in the mix. Judge it with the beat playing.
  • Cutting too deep. Large cuts make the voice hollow. Start small.
  • Using the same settings on every voice. Treat the numbers here as a first guess, then adjust by ear.
  • Skipping gain matching. A louder vocal always sounds better. Compare with the EQ on and off at the same volume.

Want to hear a finished vocal chain on your own voice first? Try our free vocal preset for Logic Pro.

FAQ

What is the best EQ for a male vocal in Logic Pro?

The stock Channel EQ is enough. Use a high-pass at about 80 Hz, a cut at 200 to 300 Hz, a boost at 3 to 5 kHz and a shelf above 10 kHz. Adjust each by ear.

Where does mud sit in a male voice?

Mud usually sits around 200 to 300 Hz, though it varies by voice and room. Sweep a boosted band to find it, then cut a few dB.

Should I high-pass a male vocal?

Yes, in most cases. About 80 Hz removes rumble without hurting the body of the voice. Lower it if the voice sounds thin.

Do I put EQ before or after compression?

Both orders work. Many producers high-pass and cut mud before the compressor, then add presence and air after it. Try each and keep the one that sounds better.

Regresar al blog

Deja un comentario

Logic Pro X Vocal Presets