Shop presets

How to Make Vocals Sound Less Nasally

GarageBand vocal presets. Add a 2nd preset for 50% off in the cart.GarageBand vocal presets. GarageBand deal: buy 1 preset, get 1 FREE.

To make a vocal sound less nasally, find the nasal band with a narrow EQ boost, then cut it by 2 to 4 dB. The nasal tone usually sits between 800 Hz and 1.5 kHz, but the exact spot changes with the voice and the mic. Fix it with your ears, not a fixed number.

I'm Warren Young. Below is the sweep method I use, plus what to check when EQ is not enough. The steps work in Logic Pro, GarageBand or any DAW with a parametric EQ.

Why does a vocal sound nasally?

Three things cause it. The singer may push sound through the nose. The mic may sit too close or on the wrong angle. Or the mix may boost the midrange, for example with heavy compression or a bright EQ boost that also lifts the honk.

Check which one you have before you EQ. Listen to the raw take with all plugins off. If it sounds nasal there, the fix starts in the recording. If it only sounds nasal after your chain, undo your last boost first.

How do I find the nasal frequency?

Use the sweep method. It takes two minutes.

  1. Open a parametric EQ on the vocal track. Add one band and make it narrow.
  2. Boost that band by about 8 dB.
  3. Play a loud part of the vocal. Slowly drag the band from 600 Hz up to 2 kHz.
  4. Stop where the voice sounds most pinched, like talking with your nose blocked. That is your problem frequency.
  5. Turn the boost into a cut of 2 to 4 dB. Widen the band slightly so the cut sounds smooth.

Switch the EQ on and off to compare. If the voice now sounds thin or dull, you cut too much. Reduce the cut by 1 dB at a time. For a full list of what each range does, see the vocal EQ cheat sheet.

What EQ settings work best?

These are starting points, not rules. Your voice and mic decide the final numbers.

  • Nasal cut: 800 Hz to 1.5 kHz, cut 2 to 4 dB, narrow to medium width.
  • Honk or cardboard sound: 400 to 800 Hz, cut a narrow band if the tone sounds hollow.
  • Warmth to balance the cut: 150 to 250 Hz, boost 1 to 2 dB if the voice now sounds thin.
  • Presence: around 3 kHz, boost 1 to 3 dB so the lyric still cuts through.

Cut narrow and boost wide. A narrow cut removes the honk without touching the rest of the voice.

Does compression make nasal vocals worse?

It can. A compressor raises the quiet parts, and the midrange gets more noticeable. If the nasal tone grows after you add compression, put the EQ cut after the compressor, or lower the amount of gain reduction. To learn the controls, read what vocal compression is and why it works.

What if EQ does not fix it?

Try these changes at the source.

  • Move the mic a few inches back and aim it slightly off the mouth.
  • Ask the singer to open the mouth more and sing from the chest, not the nose.
  • Record a new take. EQ cannot remove a nasal sound that is part of the performance.

Can a vocal preset fix a nasal sound?

A preset gives you a tuned chain to start from, with the EQ already set. It does not know your voice, so you still adjust the nasal band with the sweep above. If you use Logic Pro, try the free Toronto Warmth preset for Logic Pro X and compare it with your own chain. More Logic chains are in the Logic Pro X vocal presets collection. Presets for Logic do not load in other DAWs, so check the DAW on the product page first. On GarageBand, see the GarageBand vocal presets collection.

To see where EQ fits in a full chain, read Logic Pro vocal chain, step by step.

Frequently asked questions

What frequency is nasal in a voice?

Usually 800 Hz to 1.5 kHz. Some voices honk lower, near 500 to 800 Hz. Use the sweep method to find yours.

How much should I cut?

Start with 2 to 4 dB. Cut less if the voice turns thin. If you need more than 6 dB, fix the recording instead.

Can I fix a nasal vocal after recording?

Often yes, with a narrow EQ cut. If the sound comes from the performance, a new take gives a better result than any plugin.

Regresar al blog

Deja un comentario

Logic Pro X Vocal Presets