Shop presets

Afrobeats Vocal Chain in Logic Pro: Stock Settings

Logic Pro X vocal presets. Add a 2nd preset for 50% off in the cart.Logic Pro X vocal presets. Logic Pro X deal: buy 2 presets, get 1 FREE.

A good afrobeats vocal preset for Logic Pro is a short chain: light pitch correction, a warm EQ with a little air, gentle compression, a tempo-timed echo and wide doubles. You can build it from stock plugins in about fifteen minutes, or load a finished one.

This guide gives the chain order and starting settings, then shows what to check before you trust any preset. It is written for Logic Pro on Mac.

What makes an afrobeats vocal different?

Afrobeats vocals are melodic and warm. The lead stays close and fairly dry. Short echoes ride the groove, and wide doubles add width. So the chain has five jobs:

  • Tune lightly, so the melody is clean but still human.
  • Keep the tone warm, with a little bright air on top.
  • Keep the level even, so soft phrases are not lost.
  • Add an echo timed to the tempo, so it moves with the beat.
  • Widen the sound with doubles, and keep the lead centered.

For the base chain this page builds on, read our Logic Pro vocal settings guide. For a smoother sung style, see the R&B vocal chain for Logic Pro.

How to build an afrobeats vocal chain in Logic Pro

Select your vocal track and open the channel strip. Add the plugins in the order below. Each step feeds the next, so the order matters.

Step 1: Pitch Correction, tune lightly

Add Pitch Correction, or use Flex Pitch in the track editor. Pick the song key and use a moderate correction amount. You want the notes to land, not to snap. Hard, fast tuning gives a robotic sound that does not suit this style. Our Auto-Tune in Logic Pro guide explains both tools.

Step 2: Channel EQ, warm body and air

Turn on the high-pass filter near 80 Hz to remove rumble. If the voice sounds boxy, cut 2 to 3 dB with a narrow band between 200 and 400 Hz. Add 1 to 2 dB with a wide shelf above 8 kHz for air. Add it slowly. Too much air makes harsh "s" sounds louder, so check them with the de-esser settings for Logic Pro.

Step 3: Compressor, keep it gentle

Start with a ratio of 3:1, a medium attack and a medium release. Lower the threshold until the loudest words reduce by 3 to 5 dB. Melodic lines need to breathe, so avoid heavy squeeze. Our vocal compression settings for Logic Pro guide covers more.

Skip the setup with a finished chain

If you would rather start from a tuned chain, the R&B Vocal Preset for Logic Pro X (Dynamic R&B) loads a ready-made melodic vocal chain on your track in one click. Then adjust it by ear for your voice and your mic.

Step 4: Echo, short and in time

Add Echo and turn on tempo sync. Set the time to an eighth note, or a dotted eighth for more bounce. Keep feedback low so it repeats once or twice. Keep the mix low too. You should feel the echo between phrases, not hear it over the words. Our reverb and delay for vocals cheat sheet has more timing ideas.

Step 5: Chromaverb, add a little space

Add Chromaverb on the track, or on a send. Pick a small room and keep the mix low. The lead should stay close. A touch of space makes it sound natural, and too much pushes it behind the percussion.

Step 6: Doubles, add width

Record two extra takes of the hook, or copy the lead and offset it. Pan the doubles left and right, and keep the lead in the center. Lower the doubles in level so they support the lead. Our how to double a vocal in Logic Pro guide shows the stock method.

How do I load a vocal preset in Logic Pro?

Download the preset files and place them in the Logic Pro channel strip settings folder on your Mac. Restart Logic, open the library for your vocal track and pick the preset from the list. Our guide to installing and using Logic Pro vocal presets covers each click.

What to check in an afrobeats vocal preset

  • It was built for Logic Pro. A file made for another DAW will not load.
  • It uses stock plugins. That means no extra installs, and it opens on any Mac with Logic Pro.
  • The input level is yours to set. No preset fixes a take that clips or sits too low. Record with peaks around -12 to -6 dB.
  • It leaves room to change it. Treat a preset as a starting point. Set the key in the tuning plugin, and match the echo time to your tempo.

For the full workflow from recording to export, see the complete Logic Pro vocals guide.

FAQ

Can I make an afrobeats vocal in Logic Pro without paid plugins?

Yes. Pitch Correction, Channel EQ, Compressor, Echo and Chromaverb are stock Logic Pro plugins. They cover the whole chain in this guide.

What echo time suits afrobeats vocals?

Start with an eighth note of your project tempo, or a dotted eighth for more bounce. Lower the feedback so it repeats once or twice, and lower the mix until it only fills the gaps.

How much tuning should I use?

Use light to moderate correction. Set the song key, and keep the notes sounding natural. If you hear a robotic edge on held notes, reduce the amount.

Do I need a different preset for each song?

No. Use one chain as a base, then adjust the tuning key, compressor threshold and echo time to suit each voice and beat.

Try a free preset

You can test a finished chain before you buy anything. Download the free vocal preset (this one is a Logic Pro X file). For more presets built for Logic Pro, browse the Logic Pro X vocal presets collection.

Regresar al blog

Deja un comentario

Logic Pro X Vocal Presets