To record vocals in Logic Pro, create an audio track, choose your microphone input, and set the level so your loudest peaks reach about -12 to -6 dBFS. Turn on headphone monitoring with low latency, press Record, and capture a few takes. Then pick the best parts and move on to mixing.
These steps take about ten minutes and work with any audio interface. Settings in Logic Pro X may sit in slightly different menus between versions.
How do I set up a project to record vocals?
Step 1: Set sample rate and bit depth
Open the project settings and choose an audio sample rate and a recording bit depth. For vocals, 48 kHz and 24-bit is a safe starting point. 24-bit gives you more headroom than 16-bit, so quiet parts stay clean. Set these before you record, because changing the sample rate later can cause problems with files you already recorded.
Step 2: Create an audio track and pick the input
- Choose Track, then New Audio Track.
- Set the format to Mono. A single microphone is one channel.
- Pick the input that matches the socket your microphone uses on your interface, for example Input 1.
- Click the Record Enable button on the track, so it is ready to record.
Not sure which microphone to use? Read the best microphone for recording vocals.
Step 3: Set your input level
Sing the loudest part of the song while you watch the track meter. Turn the gain knob on your interface, not the Logic fader, until the peaks sit around -12 to -6 dBFS. This leaves headroom for a louder take. Never let the meter reach 0 dBFS, because clipping cannot be fixed later. A quiet take is easy to fix, so err on the low side.
Step 4: Set up headphones and low latency
Wear closed-back headphones so the backing track does not leak into the microphone. Turn on Input Monitoring on the track so you can hear yourself. If you hear a delay, lower the I/O Buffer Size in the audio settings, for example to 64 samples or less. Also turn on Low Latency Mode, which bypasses plugins that add delay while you record. Raise the buffer size again when you mix, because large projects need it.
| Setting | Starting value | Why |
|---|---|---|
| Sample rate | 48 kHz | Standard for music and video |
| Bit depth | 24-bit | More headroom, cleaner quiet parts |
| Track format | Mono | One microphone is one channel |
| Peak level | -12 to -6 dBFS | Room for loud notes, no clipping |
| I/O Buffer Size | 64 samples or less while recording | Low delay in your headphones |
How do I record several takes in Logic Pro?
Step 5: Use cycle recording
Set a cycle range over the verse or chorus, switch on Cycle, and press Record. Logic loops the section and records each pass as a new take. Sing the line again each time. You do not need to stop between attempts, so you stay in the flow. Do four or five passes, then stop.
Step 6: Comp the best takes
After a cycle recording, Logic keeps the passes in a take folder on the track. Open the take folder, then click the best word or phrase on any take to move it into the comp. Listen to the result, fix any rough joins, and then flatten the folder when you are happy. This gives you one strong vocal built from your best lines.
Ready to mix? Load a chain on the recorded track
Once the comp is done, you can build a vocal chain by hand or load one in a click. A Thir13een preset loads an EQ, compressor, de-esser and reverb on the recorded track, so you hear a polished vocal straight away. Browse the Logic Pro X vocal presets and adjust the result to fit your voice.
What should I do after recording?
Mixing is the next step. Start with the order of your plugins in the vocal chain guide for Logic Pro. Then even out the level with vocal compression settings in Logic Pro and tame sharp "s" sounds with de-esser settings in Logic Pro. For a wider sound, add a second take using the vocal doubler in Logic Pro.
What mistakes should beginners avoid?
- Recording too hot, so the peaks clip.
- Recording in a room with loud echo. Sing close to the microphone in a soft space, such as near curtains or a bed.
- Skipping headphones, so the backing track leaks into the take.
- Judging the sound on one take. Record several and comp.
- Adding heavy effects before you finish recording.
Try a preset on your recording
Download Toronto Warmth, our free preset for Logic Pro X, load it on your comped vocal, and hear the difference. For more options, browse the Logic Pro X vocal presets.
FAQ
What level should I record vocals at in Logic Pro?
Aim for peaks around -12 to -6 dBFS on the track meter. Set this with the gain knob on your interface. Never let the signal reach 0 dBFS.
What sample rate and bit depth should I use for vocals?
48 kHz and 24-bit is a good default. Use 24-bit for more headroom. Pick the sample rate before you record and keep it for the whole project.
Why do I hear a delay in my headphones?
The delay is latency. Lower the I/O Buffer Size, turn on Low Latency Mode, and use your interface for monitoring. Raise the buffer size again when you mix.
Do I need an audio interface to record vocals in Logic Pro?
For a studio microphone with an XLR plug, yes. A USB microphone connects straight to your Mac and shows up as an input in Logic. An interface usually gives better control of gain and latency.


