Shop presets

Podcast Vocal Chain in Logic Pro: 6 Steps to Clean Voice

Logic Pro X vocal presets. Add a 2nd preset for 50% off in the cart.Logic Pro X vocal presets. Logic Pro X deal: buy 2 presets, get 1 FREE.

A good podcast vocal chain has six steps, in this order: noise control, EQ, compression, de-essing, limiting, then a loudness check. All six come with Logic Pro as stock plugins. Set them up once, save the channel strip, and reuse it for every episode.

I have mixed spoken voice for years, and the chain is simpler than singing. You want a clear, steady voice that sits at a normal level on phone speakers and earbuds. Here are the steps and the settings I start from.

What is the best vocal chain for a podcast?

The order matters more than the plugin brands. Clean first, shape second, control levels third, protect the output last:

  1. Noise Gate or DeNoiser
  2. Channel EQ
  3. Compressor
  4. DeEsser 2
  5. Limiter
  6. Loudness Meter (to check, not to change the sound)

Treat the settings below as starting points. Every voice and room is different, so adjust by ear. For a singing chain, see Logic Pro vocal settings.

Step 1: Remove room noise first

Fix noise before anything else. A compressor raises quiet sounds, so it will also raise the hiss and hum you did not remove.

Open Noise Gate on the first insert slot. Set the threshold just above the room noise, so the gate closes between words and opens when you speak. Use a fast attack and a release long enough that word endings do not cut off. If the noise is steady, such as a fan or computer hum, try DeNoiser instead and reduce it a little at a time. Heavy noise removal makes a voice sound watery, so stop early.

Step 2: Shape the voice with Channel EQ

Put Channel EQ next. Make three moves:

  • High-pass filter around 80 Hz. This removes desk bumps and low rumble. Raise it toward 100 Hz for a thin voice.
  • Cut mud between 200 and 400 Hz by a few dB if the voice sounds boxy.
  • Add a small lift between 3 and 5 kHz for clarity, so words stay easy to follow.

Cut first, boost second. Small moves of 1 to 3 dB are usually enough for speech.

Step 3: Even out the level with Compressor

Speech jumps between quiet and loud. The Compressor pulls those jumps closer together so listeners do not reach for the volume knob.

A common starting point is a ratio of 3:1, a medium attack and a medium release. Lower the threshold until the gain reduction meter shows about 3 to 6 dB on the loudest words. Then raise the output gain to make up the lost level. If the voice sounds squashed, lower the ratio. The full method is in vocal compression settings in Logic Pro.

Want this chain already built? The Logic Pro vocal presets load an EQ, compression and de-essing chain in one click. Open one on your voice track, then adjust the gate, threshold and EQ for your mic and room.

Step 4: Tame harsh S sounds with DeEsser 2

Compression makes the S and T sounds louder in relation to the rest of the voice. That is why de-essing comes after it.

Insert DeEsser 2 and play a loud sentence with many S sounds. Set the frequency where the harshness lives, usually between 5 and 8 kHz. Raise the amount until the S sounds relax, and stop before the voice starts to lisp. Two to four dB of reduction is a sensible limit for most speakers.

Step 5: Protect the output with Limiter

The Limiter goes last on the voice channel. It catches the rare loud peak, such as a laugh or a sudden word, so the final file does not distort.

Set the output ceiling to about -1 dB. Keep the gain modest, so the limiter works only on the loudest peaks. If it reduces by more than 2 or 3 dB all the time, go back and fix the compressor instead.

Step 6: Check loudness with Loudness Meter

Put Loudness Meter on the main output and play your loudest, then your quietest, section. A common target for stereo podcasts is -16 LUFS integrated. Some platforms ask for a different number, so check your host first.

If you are above or below the target, change the gain on the voice channel or the output level, not the compressor. Match the level between episodes so listeners do not have to adjust the volume between shows.

Not sure whether a ready-made chain is worth it? Read are vocal presets worth it. You can also try the free vocal preset and open its plugins to see how a finished chain is set up.

Quick settings checklist

  • Gate or DeNoiser: close the room noise between words.
  • Channel EQ: high-pass near 80 Hz, small cut for mud, small lift for clarity.
  • Compressor: about 3:1 ratio, 3 to 6 dB of gain reduction.
  • DeEsser 2: 5 to 8 kHz, 2 to 4 dB at most.
  • Limiter: ceiling around -1 dB.
  • Loudness Meter: common target -16 LUFS, stereo.

Record close to the mic in a quiet room first. No chain can fully fix a poor recording, but a good one makes a good recording sound finished.

Frequently asked questions

What order should podcast vocal plugins go in?

Noise control, EQ, compressor, de-esser, limiter. Clean the signal first, then shape it, then control the level. Use the Loudness Meter on the main output at the end.

What loudness should a podcast be?

A common target is -16 LUFS for stereo. Your hosting platform may publish its own target, so check it before you export.

Can I use GarageBand for a podcast vocal chain?

The same order applies in any DAW. This guide names Logic Pro plugins. If you use GarageBand, check which of these plugins it includes and build the same order with what you have.

Back to blog

Leave a comment

Logic Pro X Vocal Presets