Shop presets

How to Mix Background Vocals in Logic Pro (6 Steps)

Logic Pro X vocal presets. Add a 2nd preset for 50% off in the cart.Logic Pro X vocal presets. Logic Pro X deal: buy 2 presets, get 1 FREE.

To mix background vocals in Logic Pro, group them on one bus, cut the low end and the mud, compress them harder than the lead, pan them apart, and send them to a shared reverb. Then set the level so they support the lead and never fight it. Follow the order below and use the table for starting values.

Backing vocals fail for one reason: they take the same space as the lead. The steps below give them their own place in the mix. For the lead, see the Logic Pro vocal chain, step by step.

Step 1: How do I organize background vocals in Logic Pro?

  1. Name every track. Use clear names: Harmony High, Harmony Low, Ad-libs, Doubles.
  2. Make a Track Stack. Select the backing tracks, then choose Track > Create Track Stack and pick Summing Stack. One fader now controls all of them.
  3. Match the take first. Cut breaths and noise between phrases. Line up the start and end of each word across the stack, so the voices land together.

Step 2: How do I EQ background vocals?

Add Channel EQ on each track, or one on the stack. Cut so the lead keeps its space.

  • High-pass at about 100 to 150 Hz. Backing vocals do not need the low end, and the lead and the bass use it.
  • Cut 2 to 3 dB around 250 to 400 Hz if the stack sounds boxy.
  • Cut 1 to 3 dB around 2 to 4 kHz if the stack covers the lead. This leaves the lead's presence area free.
  • Roll off a little above 10 kHz if the stack sounds bright and hissy.

Step 3: How do I compress background vocals?

Use Compressor on the stack. Backing vocals should sound even and steady, so you can compress them more than the lead. Start at a ratio of 4:1, attack 10 to 20 ms, release 60 to 100 ms, and aim for 4 to 8 dB of gain reduction. If the "s" sounds poke out, add DeEsser 2 (see de-esser settings in Logic Pro). For more on the settings, read vocal compression settings in Logic Pro.

Step Logic Pro plugin Starting value What it fixes
EQ Channel EQ High-pass 100 to 150 Hz; cut 2 to 3 dB at 250 to 400 Hz Low-end build-up and mud
EQ Channel EQ Cut 1 to 3 dB at 2 to 4 kHz Fighting the lead
Compression Compressor 4:1, attack 10 to 20 ms, release 60 to 100 ms, 4 to 8 dB reduction Uneven level
De-ess DeEsser 2 Reduce 3 to 5 dB at 5 to 8 kHz Harsh "s" from stacked voices
Delay send Tape Delay or Echo 1/8 note, low feedback, send low Depth without blur
Reverb send ChromaVerb Room or plate, about 1 to 1.8 seconds Shared space

Want this chain already built?

The Logic Pro X vocal presets load an EQ, compressor and effects chain in one click. Load one on the backing stack, then adjust the EQ cuts above by ear.

Step 4: How do I pan background vocals?

Keep the lead in the center. Spread the backing vocals around it so the stack sounds wide and the center stays clear.

  • Pan pairs in opposite directions: one high harmony left, one right.
  • Pan doubles of the same line left and right by the same amount.
  • Keep ad-libs off to one side, or move them between sections.

To make the doubles themselves, see how to double vocals in Logic Pro. Check the mix in mono. If the backing vocals vanish, the voices cancel each other, so change the pan of one take or nudge its timing.

Step 5: How do I add reverb and delay to background vocals?

Use sends, not inserts. Create a Bus send from the backing stack to an Aux with ChromaVerb, and another to an Aux with Tape Delay. Raise the send until you hear the space, then lower it a little. Backing vocals can take more reverb than the lead because the lead stays dry and close. Keep the reverb darker, so it does not add harshness. For settings, see reverb and delay for vocals: settings cheat sheet.

Step 6: How loud should background vocals be?

Set the level with the full beat playing. Start with the stack faders down, then raise them until the harmony fills out the lead, then stop. If you can pick out each backing word at normal volume, they are too loud. Check on earbuds and a phone speaker. For chorus lines that need lift, automate the stack up 1 to 2 dB for the hook instead of adding more compression.

What mistakes ruin background vocals?

  • No high-pass filter, so the stack adds mud under the lead.
  • Different timing between takes, so the voices smear.
  • Too much reverb on every track, so the stack sounds distant and blurry.
  • Backing vocals as loud as the lead.
  • Many plugins on each track. Remove any plugin you cannot hear when you bypass it.

For more settings, see Logic Pro vocal settings.

Try a preset on your backing vocals

Browse the Logic Pro vocal presets for a finished chain. To try one first, download Toronto Warmth, our free preset for Logic Pro X.

FAQ

Should background vocals be louder or quieter than the lead?

Quieter. They should support the lead and fill out the sound. If a listener notices the backing words first, lower the stack.

Should I compress background vocals?

Yes. Compress them more than the lead so they stay even and sit behind it. Start with 4 to 8 dB of gain reduction and adjust by ear.

How do I make background vocals sound wide?

Pan harmonies and doubles to opposite sides, keep the lead in the center, and use a shared reverb send. Check the mix in mono to be sure nothing disappears.

Do background vocals need their own reverb?

Give the stack its own reverb send. Keep the send level higher than the lead's, and use a darker setting so the space does not add harshness.

Back to blog

Leave a comment

Logic Pro X Vocal Presets