Shop presets

How to Make Vocals Wider in Logic Pro

Logic Pro X vocal presets. Add a 2nd preset for 50% off in the cart.Logic Pro X vocal presets. Logic Pro X deal: buy 2 presets, get 1 FREE.

To make vocals sound wider in Logic Pro, keep the lead vocal in the center and widen the support around it. Duplicate the vocal, pan the copies left and right, and add Stereo Spreader or a short delay to the copies. The lead stays solid, and the space grows around it.

Widening the lead itself is the most common mistake. It thins the voice and can vanish in mono. The steps below keep the center strong.

How to make vocals wider in Logic Pro

  1. Keep the lead vocal centered, with no stereo effect on it.
  2. Record or duplicate a double of the lead.
  3. Pan the double and its copy hard left and right.
  4. Roll off the low end of the doubles with Channel EQ.
  5. Add a short delay or Stereo Spreader to the doubles only.
  6. Check the mix in mono.

Step 1: Build wide vocal doubles

Duplicate the lead track twice, or record two new takes of the same line. Pan one track left and the other right, about 40 to 70 percent each side. Lower both by 6 to 10 dB under the lead. Panning is done with the Pan knob on each channel strip.

Real takes sound wider than copies because tiny timing and pitch differences are natural. A copy of the same audio only widens when you add an effect in the next steps.

Cut the low end of the doubles

Insert Channel EQ on each double. Turn on the high-pass filter at about 150 to 250 Hz. The low end stays in the center, which keeps the mix tight and the mono sound clean.

Step 2: Use a short delay for width (the Haas effect)

A very short delay on one side makes the brain place the sound off to the side. On the right double, insert Stereo Delay and set a delay of 10 to 30 ms with no feedback. Keep the wet level full on that track, so you hear only the delayed signal.

Under 10 ms, the vocal starts to sound hollow. Above 40 ms, you hear a separate echo. Start near 20 ms and adjust by ear.

Let a preset build the chain

You can build every layer by hand, or load a finished chain on the vocal track. A Thir13een preset sets the EQ, compression and effects in one click, so you start from a clean, balanced vocal and add width on top. Try the Vocal Preset Starter Pack for Logic Pro X.

Step 3: Stereo Spreader and Chorus on the doubles

Stereo Spreader splits the frequency range between the left and right sides. Insert it on a bus that holds only the doubles. It works best on the upper range, so keep the low frequency setting high enough that bass and body stay centered.

Chorus adds gentle movement. Use a low depth and a slow rate, and set the mix low, so the voice does not sound seasick. Put Chorus on the doubles, not on the lead.

Step 4: Widen with a delay send

Create a send from the lead to a bus with Stereo Delay or Delay Designer. Set the delay to a note value that fits your tempo, such as an eighth note, and lower the feedback. Cut the highs and lows of the return with Channel EQ. The lead stays dry and centered, and the echoes spread to the sides.

How to check that wide vocals still work in mono

Phones, clubs and some speakers sum the mix to mono. Wide effects can then cancel parts of the vocal. Test it in Logic: insert Direction Mixer on the master and turn Spread down to fold the sides together, then remove it after the check. If the doubles vanish or sound thin, reduce Stereo Spreader or lengthen the short delay.

Before you widen, make sure the base vocal is clean. See our guides to fixing muddy vocals and vocal compression settings in Logic Pro. For the full signal order, read Logic Pro vocal settings. Control sharp "s" sounds on bright doubles with de-esser settings.

FAQ

Should I widen the lead vocal?

No. Keep the lead centered. Widen the doubles, the backing vocals and the delay returns. A centered lead stays clear on every speaker.

Why does my wide vocal sound thin?

Phase problems are the usual cause. Two identical tracks with a very short delay can cancel in mono. Raise the delay time, lower the effect amount, and check the mix in mono.

How wide should the doubles be panned?

Start at 40 to 70 percent left and right. Hard panning at 100 percent gives the widest sound, but it can feel disconnected from the lead on headphones.

Try it on a finished chain

Download the free vocal preset for Logic Pro X and test your widening on a ready-made chain. For more, browse the Logic Pro X vocal presets.

Back to blog

Leave a comment

Logic Pro X Vocal Presets