Shop presets

GarageBand Vocal Compression Settings (Step by Step)

GarageBand vocal presets. Add a 2nd preset for 50% off in the cart.GarageBand vocal presets. GarageBand deal: buy 1 preset, get 1 FREE.

For lead vocals in GarageBand, start the Compressor at a 3:1 ratio, a threshold of about -20 dB, an attack of 15 ms, a release of 80 ms, and 2 to 4 dB of makeup gain. Then lower the threshold until the gain reduction meter shows 3 to 6 dB on the loudest words. These are starting points, so adjust them to your voice.

I use GarageBand on Mac for demo vocals. This guide shows the setting for each knob and how to hear when it is right. If you use Logic, read vocal compression settings in Logic Pro.

Where to find the Compressor in GarageBand

Select the vocal track and open Smart Controls. Open the Plug-ins section and click an empty slot. Choose Compressor. Set Auto Gain to off, so you set the level yourself. Fix noise first: see how to remove vocal noise in GarageBand. A compressor also lifts quiet noise.

Best GarageBand compressor settings for vocals

Control Start here What it does
Ratio 3:1 Sets how much the compressor turns down peaks over the threshold.
Threshold -20 dB (adjust) Sets the level where compression starts.
Attack 15 ms Lets the start of each word through, so the vocal keeps its punch.
Release 80 ms Sets how fast the compressor lets go after a loud word.
Gain (makeup) +2 to +4 dB Brings the level back up after compression.

How to set the threshold

Play the loudest part of the vocal. Lower the Threshold slowly until the gain reduction meter moves 3 to 6 dB on the loud words. For a soft verse, aim for 2 to 3 dB. If the meter moves more than 8 dB, raise the threshold or lower the ratio.

How to set attack and release

A slow attack (15 to 30 ms) keeps consonants clear. A fast attack (under 5 ms) makes the vocal sound flat. For release, try 60 to 120 ms. If the vocal pumps or the end of words sounds cut, lengthen the release. For fast rap, use a shorter release.

How to set makeup gain

Turn the Gain knob up until the compressed vocal plays at the same loudness as the bypassed one. Switch the plug-in on and off to compare. Louder always sounds better, so match the level before you judge.

Want this chain loaded in one click? The Hip-Hop Vocal Preset Bundle for GarageBand gives you ready-made vocal chains for GarageBand. Load a preset on your vocal track, then adjust the Compressor to fit your voice.

Common vocal compression mistakes in GarageBand

  • Too much ratio. A ratio of 8:1 or higher turns a vocal into a flat, tight sound. Keep the ratio at 2:1 to 4:1 for singing.
  • Threshold too low. If the meter always shows heavy gain reduction, the compressor works on every word. Raise the threshold.
  • Attack too fast. The vocal loses its punch and sounds dull.
  • No level match. If you do not set the makeup gain, you cannot tell if the compressor helps.
  • Fixing the wrong problem. Compression does not fix a bad recording. Record at a healthy level, with no clipping, then compress.

Compress twice for a smoother vocal

If one compressor works too hard, use two. Put a first Compressor at 2:1 with 2 to 3 dB of gain reduction. Add a second one at 3:1 with 2 to 3 dB. Two light stages sound more natural than one heavy stage. Check the gain reduction meter on each plug-in.

How to check the result

Listen against the beat at normal volume. Every word should be clear, and no word should jump out. Quiet words should not sink under the beat. Add EQ after compression: see GarageBand vocal EQ settings. For more ready chains, browse the GarageBand vocal presets collection.

FAQ

What ratio should I use for vocals in GarageBand?

Start at 3:1 for lead vocals. Use 2:1 for a gentle, natural sound. Use 4:1 for a tighter rap vocal.

Should I use a fast or slow attack on vocals?

Use a slow to medium attack, 15 to 30 ms. This lets the start of each word through and keeps the vocal clear.

How much gain reduction is right?

For most vocals, 3 to 6 dB on the loudest words. Over 8 dB often sounds squashed.

Do I compress before or after EQ?

Many producers cut low rumble with EQ first, then compress. Test both orders and keep the one that sounds better.

Try it first on a free preset: get the free vocal preset.

Back to blog

Leave a comment

Logic Pro X Vocal Presets