Shop presets

How to Fix Harsh Vocals in Logic Pro

Logic Pro X vocal presets. Add a 2nd preset for 50% off in the cart.Logic Pro X vocal presets. Logic Pro X deal: buy 2 presets, get 1 FREE.

To fix harsh vocals in Logic Pro, cut 2 to 4 dB with a narrow band on Channel EQ between 2 and 5 kHz, then tame the "s" sounds with DeEsser 2 around 5 to 8 kHz. Harsh means too much upper-mid energy, so you reduce that range instead of turning the whole vocal down.

The settings below are starting points. Move each one by ear for your voice and your mic.

How to fix harsh vocals: the quick version

  1. Find the harsh spot with a boosted, narrow sweep from 2 to 5 kHz.
  2. Turn that boost into a 2 to 4 dB cut.
  3. Add DeEsser 2 if the "s" and "t" sounds still sting.
  4. Compress gently after the EQ, not before.
  5. Check the vocal against the beat. Bright samples can add harshness too.

What makes vocals sound harsh?

Our ears are most sensitive between 2 and 5 kHz, so small build-ups there sound painful. Common causes are:

  • A bright or cheap condenser mic aimed straight at the mouth.
  • Singing loud and close, which pushes the upper mids.
  • Compression that lifts quiet sibilance and edge.
  • Too much high-shelf boost to "add air".
  • A beat with hi-hats, snares or synths that crowd the same range.

Harsh vocal frequencies: what to cut

Range What you hear What to do
1 to 2 kHz Honk, nasal edge Small cut only if still honky
2 to 5 kHz Harsh, piercing, fatiguing Cut 2 to 4 dB with a narrow band
5 to 9 kHz Sharp "s" and "t" sounds (sibilance) De-esser, not EQ
Above 10 kHz Hiss and fizz Reduce a high shelf you added

Cut small amounts. A cut of more than 5 dB usually makes a voice dull.

Channel EQ and DeEsser 2 settings for harsh vocals

Step 1: Find the harsh spot

Insert Channel EQ on the vocal. Pick an upper-mid band, set Gain to +6 dB and a narrow Q. Sweep from 2 to 5 kHz while the vocal plays. When the sound is most painful, stop. That is your problem frequency.

Step 2: Turn the boost into a cut

Set Gain to -2 to -4 dB at that frequency and widen the Q a little. Switch the plugin on and off. The vocal should sound smoother, not muffled.

Step 3: Add DeEsser 2 for sharp "s" sounds

If the harshness is mostly sibilance, EQ will dull the whole voice. Insert DeEsser 2 instead. Set the frequency near 5 to 8 kHz, then raise Strength until the "s" sounds stop stinging. Our de-esser settings for Logic Pro give exact starting values.

Let a preset build the chain

You can build this by hand, or load a finished chain on the track. A Thir13een preset loads the EQ, de-esser, compression and effects on your vocal in one click, so you hear a smooth starting point and adjust it. Try the Vocal Preset Starter Pack for Logic Pro X, or browse the Logic Pro X vocal presets.

Stop compression from making vocals harsh

A compressor raises quiet parts, and that includes edge and breath. Put EQ and de-essing before Compressor, and use a low ratio of about 3:1 with a slow-to-medium attack. See our vocal compression settings for Logic Pro for the full setup.

If the harshness comes and goes with loud notes only, Multipressor can compress just the upper-mid band. Set one band around 2 to 5 kHz and let it work only when that range gets loud.

Is it the vocal or the mix?

If the vocal sounds fine alone but harsh with the beat, cut the same 2 to 5 kHz range on the beat or synths by 1 to 2 dB. This leaves room for the voice.

Check the opposite problem too. If the vocal now sounds boxy or cloudy, read how to fix muddy vocals. For the full signal order, see Logic Pro vocal settings.

Try a preset on your vocal

Download Toronto Warmth, our free preset for Logic Pro X, load it on your vocal and hear a finished chain. For more options, browse the Logic Pro X vocal presets.

FAQ

What frequency makes vocals harsh?

Mostly 2 to 5 kHz. Sharp "s" sounds sit higher, around 5 to 9 kHz. Sweep a narrow boosted band to find the exact spot for your voice.

Should I use EQ or a de-esser for harsh vocals?

Use EQ for a constant harsh tone and a de-esser for sharp "s" and "t" sounds. Many vocals need both, with the EQ first.

Why does my vocal sound harsh after recording?

Usually mic choice, mic position or loud, close singing. Move back 15 to 20 cm, angle the mic slightly off-axis and lower the input gain so loud notes do not push the edge.

Back to blog

Leave a comment

Logic Pro X Vocal Presets