5 Ways To Make Vocals Sound Better


Vocal processing is one of the most easiest things in theory, but one of the hardest to accomplish in practice. Here are 5 ways to make vocals sound better now

1. Use Automation To Control Volume

Automation means having a DAW (Logic Pro X, Pro Tools, Ableton, etc.) automatically perform tasks over time, particularly moving knobs, faders, and switches for you.

The most popular use of automation in mixing is to adjust the volume of a track.
For example, it allows you to bring an instrument to the forefront for a moment and fade it back out when the lead vocal comes back in. Take a look at the example below and notice how the fader on the left moves automatically based on the automation curves on the track on the right.

Volume Automation
Source - Izotope.com

2. Use A De-Esser


A de-esser is a simple tool that goes a long way in making your mixes sound professional. A de-esser allows us to compress the sibilance in our vocals.

Sibilance is a type of sound that often seems harsh in the context of a recording. Typically “S” and “T” are the worst offenders. The rest of your vocal chain could sound perfect, but words like “Specialty” may sound overwhelming because of sibilance.

When using a de-esser, follow these 5 simple steps to make sure you get it right every time.

  1. Place your de-esser after your EQ and Compression.
  2. Find the frequency where sibilance is most present.
  3. Set your threshold (or sensitivity) so the de-esser is only turning on when sibilance is present.
  4. Turn up the de-esser’s strength until the vocalist “S’s” and “T’s” are hard to hear. Then dial the strength back a little bit.
  5. Set the smoothing so the gain reduction sounds natural, usually between 8 and 18 ms.

Source - Musicianonamission

3. Catch Peaks With A Limiter



Hard Limiter is like an extreme compressor effect, reducing the dynamic range of the audio. Where the waveform exceeds the level set in "dB limit" it is clipped down, so reducing the peak level. Hard Limiter can also sometimes be used to remove stubborn clicks that peak well above the general level of the waveform."

Basically, the hard limiter is used to make the peaks of the waveform flat. In the above quote, "clipping" is used to refer to the flattening of the waveform, but below is the more common use of the word.

4. High End Boost (AIR)




This is perhaps the easiest and fastest way to make a vocal sound expensive.

Most boutique microphones have an exaggerated top-end. When using a more affordable microphone, you can simply boost the highs to replicate this characteristic.

The best way to do this is with an analogue modelling EQ, such as the free Slick EQ. Use a high shelf, and start with a 2dB boost at 10kHz.

Experiment with the frequency and amount of boost. You can go as low as 6kHz (but keep it subtle) and boost as much as 5dB above 10kHz. Just make sure it doesn’t become too harsh or brittle.

Source - Tunecore.com

5. Remove Room Resonance


There are situations when the unpleasant resonances are basically all in the signal’s indirect parts, caused by the reflections of the room. So, the idea is to heavily emphasize the direct parts of the recording at 400 Hz. To do so, we need to move the proximity band upwards at 400 Hz – the plug-in automatically attenuates the reverb parts at this area of the spectrum.


The result: the resonance is gone but this time the violin sounds as rich and full as before. By eliminating the room information at 400 Hz, we killed the resonances without negatively impacting the frequency spectrum of the direct signal.


Source - Sonible

Download FREE Rap Vocal Preset for Logic Pro X

Want a crisp, clean and more full of life vocal than your original? Download your free rap vocal preset for logic pro now and achieve the professional audio sound you've always dreamed of.

Warren 'Thir13een Beatz' Young 
Professional producer, singer and music coach.